Shark Pro | Interior Windshield Warning Light | ECE R65 &amp

Shark Pro | Interior Windshield Warning Light

Shark Pro | Interior Windshield Warning Light | ECE R65 & ECE R10 Approved | 10–30V DC

Item No.: 115

5.0 / 10 reviews

from 158,69 €

incl. 19% VAT plus

Net: 133,35 €

Amber

Blue

DualColor

Do you want to order multiple variants at once?

Available immediately

Product Description

Compact. Flexible. Windshield-mountable.

The windshield beacon Shark Pro from Raptors LED Technik® is a professional front flashing unit with an ECE R65-tested LED module. With its compact dimensions of 252 mm length, 116 mm width and 76 mm height (including suction cup) it can be flexibly mounted on the windshield. A foam padding on the edge protects the glass from scratches and reduces reflections for glare-free driving.

💡 Technology & Performance

Signal-intensive high-power LEDs (5 W per LED)
120 flashes per minute for clear warning effect
Dual-color version with color change via vehicle plug
Flash pattern selection directly on the vehicle plug
Adjustable beam angle for different windshield positions
Multi-voltage 10–30 V DC
Protection class IP57

🛠️ Mounting & Accessories

Quick mounting with suction cup or adhesive tape
Foam edge for scratch-free attachment and reduced reflections
Cable length: 3000 mm

🟠 Synchronization

Multiple units synchronizable
Supports 1-, 2- and 4-channel flash patterns

🎛️ Operation & Control

Direct control via vehicle plug
Color selection (dual-color) and flash pattern switching via switch on the plug

✅ Approvals & Standards

ECE R65 (LED module)
ECE R10
Category XA1 / XB1

Technical Data
I L x W x H: 252 × 116 × 76 mm (with suction cup)
I Number of LEDs: High-power LEDs (5 W per LED)
I Flash frequency: 120 flashes / minute
I Operating voltage: 10–30 V DC
I Protection class: IP57
I Operating temperature: –30 °C to +60 °C
I Cable length: 3000 mm
I Conductor cross-section: 0,25 mm²

Please read the instructions carefully and adhere to the regulations and guidelines listed before operating the device.

WARNING Risk of Injury!

The optical radiation from LED products can damage your eyes.
Never look directly into the light of LED products.

General Safety Instructions - Installation

Installation, commissioning, and maintenance should only be performed by qualified electricians.
Never work on the device while it is live. Risk of fatal electric shock!
Never exceed the permissible voltage specified in this manual.
Do not remove the housing to avoid the risk of electric shock.
LED products must be installed in compliance with the electrical and mechanical safety regulations applicable in your country.
Ensure that the connection cables are laid without kinks, pinches, or sharp edges during installation.
If drilling holes into the structure of the vehicle is necessary for permanent installation, ensure that the vehicle surface is not damaged (e.g., by corrosion). Be cautious not to damage cables or load-bearing components while drilling.

General Safety Instructions - Usage

Avoid extreme temperatures or strong vibrations.
LED products may only be used within the temperature ranges specified in the manual.
Ensure LED products are only operated in accordance with their protection class (IP rating) and are not exposed to prolonged moisture or heavy rain if it falls outside the specified protection class.
Any mechanical stress or load on LED products is prohibited.
LED products must not be used in environments where the presence of flammable gases, vapors, or dust is possible.
Disconnect the LED product from the power supply when not in use or during cleaning (e.g., unplug the connector, trip the fuse, etc.).

Safety Instructions for Magnetic Mounts

Magnetic mounts generate strong forces that can cause injuries if mishandled. Be especially careful to avoid pinching fingers or hands.
Keep magnets away from sensitive devices and objects, such as electronic devices (e.g., smartphones, laptops), magnetic storage media (e.g., credit cards, hard drives), and watches. Such items can be damaged or rendered unusable by magnetic fields.
Store magnets safely when not in use and away from sensitive materials to prevent accidental damage. Preferably keep them in their original packaging.

Special Instructions for Individuals with Medical Implants

Warning: Individuals with pacemakers, implanted defibrillators, or other medical implants must avoid close proximity to strong magnetic fields.

Magnets can significantly disrupt or deactivate such devices, leading to life-threatening situations.
Users with medical implants are strictly prohibited from handling products or accessories with magnetic mounts to ensure their safety.
Maintain a safe distance from magnetic fields, even if the magnets are packaged or not actively in use.

Target Audience

The use and operation of the LED product are permitted only by trained and instructed personnel.
Children must be kept away from LED products. Children and individuals with limited physical, sensory, or cognitive abilities, or lack of experience and knowledge, may only use LED products under supervision.

Cleaning and Maintenance

Perform a thorough visual inspection of the device for cracks, discoloration, damage, contamination, and the condition of seals before each use and at regular intervals. Ensure that glass and seals are properly positioned and fully tightened to prevent water ingress.
Regularly check that all screws and fittings are tightened, especially after vibrations or shocks, to ensure secure mounting.
Improper cleaning of the LED product can cause damage. Do not use aggressive cleaning agents, brushes with metal or hard bristles, or sharp or metallic cleaning tools. During vehicle washes, avoid applying high pressure directly to the installed LED products.

Driving with Mounted Products (Permanently Installed or Magnetic Mounts)

Aerodynamic Effects

The installation of additional products, regardless of the mounting type, affects the vehicle's aerodynamics. This can increase air resistance and impact driving stability, especially at higher speeds.
Adjust your speed according to the changed driving conditions and wind load to ensure safe driving behavior.

Adaptation to Weather Conditions

In adverse weather conditions such as strong winds, rain, snow, or ice, reduce your speed to prevent the mounted products from lifting or detaching.
Note that wind and pressure on the products during rain or snowfall may be stronger and can impact adhesion or stability. Regularly check the mounting.

Secure Hold with Magnetic Mounts

Magnetic mounts can be affected by vibrations, strong wind loads, or uneven roads. Check the secure fit of the magnetic mount before starting your journey and regularly during long trips.
Ensure that the mounting surface is clean and free of grease to ensure optimal adhesion. Loose or inadequately secured products pose a safety risk.

Note on DEKRA-Certified Products

The respective products have been tested by DEKRA under optimal conditions at speeds of up to 220 km/h. These test values apply only under ideal conditions such as dry roads, stable mounting surfaces, and calm wind conditions. Under adverse weather conditions, uneven roads, or other challenging circumstances, these values cannot be guaranteed. Therefore, regular inspection of the mounting is essential to ensure safety.

Speed Limit and Load

The maximum permissible speed according to the manufacturer's specifications must not be exceeded. Exceeding these limits can not only damage the product but also compromise road safety.
During highway driving, regular inspection of the mounting is essential, as the resulting wind and vibrations increase significantly with speed.

Safety Instructions and Warnings for Products with Integrated Batteries

Storage and Handling

Do not store the product in wet, damp, or dusty places.
Avoid placing heavy objects on the product to prevent damage.
Do not expose the product to excessive heat or store it near flammable materials.

Charging the Product

The product should only be charged using original accessories.
Ensure no foreign objects enter the connections (charging port and power plug). Foreign objects can cause fire or electric shock.

Integrated Battery

The integrated battery must not be removed or replaced independently for safety reasons.

Maintenance and Inspection

Fully charge the battery before first use and ensure the product functions properly.
Charge the battery at least every 6 months to ensure optimal performance.
Inspect the product regularly, especially with prolonged use.

Battery Storage

Batteries should only be stored within a temperature range of -20 °C to +40 °C to ensure their safety and performance.
Do not store products with batteries in vehicles, as extreme heat above +40 °C can occur in the interior during high outdoor temperatures, causing damage or hazards such as overheating or fire.
Keep the product in a cool, dry, and well-ventilated place away from direct sunlight.

Disposal

The integrated battery must not be improperly disposed of. Observe the applicable regulations for the disposal of batteries and electronic devices in your region.
Burning, disassembling, or independently removing the battery is prohibited and can cause damage or hazards.

Note: The batteries built into this product are not classified as hazardous materials when used as intended.

Raptors LED Technik®
Ruth Schwob Str. 14
D-74924 Neckarbischofsheim

Tel.: +49 (0)7263 4087078
Mail.: info@raptors-led-technik.de

Average item rating

Share your experiences with other customers!

All reviews:

How do reviews work?

Manufacturer according to GPSR
Raptors LED Technik®, www.raptors-led-technik.com

Cookiename	Beispielinhalt	Ablaufzeit
_ga_*	deleted	730 Tage
_ga	GA1.1.8643343795.1726666186	730 Tage

Shark Pro | Interior Windshield Warning Light | ECE R65 & ECE R10 Approved | 10–30V DC

Tolle Leuchte

Sehr tolles Produkt

Sehr hochwertig

Schöner Blitzer

Sehr hcohwertiges Produkt

Super Artikel

Toller Blitzer

Hochwertig

Super Leuchte

Bester Frontblitzer