Lightbar SLIM with Controller - ECE R65

(22 Reviews)

SKU: 186

Available immediately

from 773,03 €

excl. 19% VAT , plus

Größe
Bedieneinheit
Leuchtfarbe

PDF offer

This item has variations. Please select the requested variation.

Equipped with the latest LED technology, our new SLIM lightbar has a convincing luminous efficacy.

The LED modules with very fast flash sequence are positioned in such a way that a light emission of 360 degrees is possible. The LED modules also have a long and maintenance-free service life and a multi-voltage of 10-30V DC. The integrated rear warning system with its 3 different modes ensures optimum protection of danger zones.
The modern technology is protected from below by an aluminum-reinforced base and from above by a break-resistant and impact-resistant black polycarbonate. The LED light warning bar can be mounted quickly and safely on the vehicle roof. The required material is included with the delivery of the LED light warning bar.

The beam comes standard with a 10-30V DC CAR plug. With this you can switch the bar on and off as well as change the flash patterns. The beam can also be permanently installed without this plug.

In addition, you have the possibility to purchase our WIFI remote control. With this you control the bar completely wirelessly in mobile phone format.

Admission:
I ECE R65
I ECE R10
I Category TA2
I 1,2,3,4x flash, both sides or alternating

Technical data:
I LxWxH: 120cm - 150cm x 21,8cm x 2,5cm (without stand)
I Number of LEDs: 72-192 LEDs ( 5730SMDs )
I Cable length beam 5m
I Power: 106W-122W
I Operating voltage: 10-30V DC
I Protection class: IP65
I Working temperature: -30° C - +50° C
I Visibility: Up to 6000m

Scope of delivery:
I Roof system SLIM
I Screw fastening
I 10-30V car plug 3.5m (Wifi controller optional)

Please read the instructions carefully and adhere to the regulations and guidelines listed before operating the device.

WARNING Risk of Injury!

The optical radiation from LED products can damage your eyes.
Never look directly into the light of LED products.

General Safety Instructions - Installation

Installation, commissioning, and maintenance should only be performed by qualified electricians.
Never work on the device while it is live. Risk of fatal electric shock!
Never exceed the permissible voltage specified in this manual.
Do not remove the housing to avoid the risk of electric shock.
LED products must be installed in compliance with the electrical and mechanical safety regulations applicable in your country.
Ensure that the connection cables are laid without kinks, pinches, or sharp edges during installation.
If drilling holes into the structure of the vehicle is necessary for permanent installation, ensure that the vehicle surface is not damaged (e.g., by corrosion). Be cautious not to damage cables or load-bearing components while drilling.

General Safety Instructions - Usage

Avoid extreme temperatures or strong vibrations.
LED products may only be used within the temperature ranges specified in the manual.
Ensure LED products are only operated in accordance with their protection class (IP rating) and are not exposed to prolonged moisture or heavy rain if it falls outside the specified protection class.
Any mechanical stress or load on LED products is prohibited.
LED products must not be used in environments where the presence of flammable gases, vapors, or dust is possible.
Disconnect the LED product from the power supply when not in use or during cleaning (e.g., unplug the connector, trip the fuse, etc.).

Safety Instructions for Magnetic Mounts

Magnetic mounts generate strong forces that can cause injuries if mishandled. Be especially careful to avoid pinching fingers or hands.
Keep magnets away from sensitive devices and objects, such as electronic devices (e.g., smartphones, laptops), magnetic storage media (e.g., credit cards, hard drives), and watches. Such items can be damaged or rendered unusable by magnetic fields.
Store magnets safely when not in use and away from sensitive materials to prevent accidental damage. Preferably keep them in their original packaging.

Special Instructions for Individuals with Medical Implants

Warning: Individuals with pacemakers, implanted defibrillators, or other medical implants must avoid close proximity to strong magnetic fields.

Magnets can significantly disrupt or deactivate such devices, leading to life-threatening situations.
Users with medical implants are strictly prohibited from handling products or accessories with magnetic mounts to ensure their safety.
Maintain a safe distance from magnetic fields, even if the magnets are packaged or not actively in use.

Target Audience

The use and operation of the LED product are permitted only by trained and instructed personnel.
Children must be kept away from LED products. Children and individuals with limited physical, sensory, or cognitive abilities, or lack of experience and knowledge, may only use LED products under supervision.

Cleaning and Maintenance

Perform a thorough visual inspection of the device for cracks, discoloration, damage, contamination, and the condition of seals before each use and at regular intervals. Ensure that glass and seals are properly positioned and fully tightened to prevent water ingress.
Regularly check that all screws and fittings are tightened, especially after vibrations or shocks, to ensure secure mounting.
Improper cleaning of the LED product can cause damage. Do not use aggressive cleaning agents, brushes with metal or hard bristles, or sharp or metallic cleaning tools. During vehicle washes, avoid applying high pressure directly to the installed LED products.

Driving with Mounted Products (Permanently Installed or Magnetic Mounts)

Aerodynamic Effects

The installation of additional products, regardless of the mounting type, affects the vehicle's aerodynamics. This can increase air resistance and impact driving stability, especially at higher speeds.
Adjust your speed according to the changed driving conditions and wind load to ensure safe driving behavior.

Adaptation to Weather Conditions

In adverse weather conditions such as strong winds, rain, snow, or ice, reduce your speed to prevent the mounted products from lifting or detaching.
Note that wind and pressure on the products during rain or snowfall may be stronger and can impact adhesion or stability. Regularly check the mounting.

Secure Hold with Magnetic Mounts

Magnetic mounts can be affected by vibrations, strong wind loads, or uneven roads. Check the secure fit of the magnetic mount before starting your journey and regularly during long trips.
Ensure that the mounting surface is clean and free of grease to ensure optimal adhesion. Loose or inadequately secured products pose a safety risk.

Note on DEKRA-Certified Products

The respective products have been tested by DEKRA under optimal conditions at speeds of up to 220 km/h. These test values apply only under ideal conditions such as dry roads, stable mounting surfaces, and calm wind conditions. Under adverse weather conditions, uneven roads, or other challenging circumstances, these values cannot be guaranteed. Therefore, regular inspection of the mounting is essential to ensure safety.

Speed Limit and Load

The maximum permissible speed according to the manufacturer's specifications must not be exceeded. Exceeding these limits can not only damage the product but also compromise road safety.
During highway driving, regular inspection of the mounting is essential, as the resulting wind and vibrations increase significantly with speed.

Safety Instructions and Warnings for Products with Integrated Batteries

Storage and Handling

Do not store the product in wet, damp, or dusty places.
Avoid placing heavy objects on the product to prevent damage.
Do not expose the product to excessive heat or store it near flammable materials.

Charging the Product

The product should only be charged using original accessories.
Ensure no foreign objects enter the connections (charging port and power plug). Foreign objects can cause fire or electric shock.

Integrated Battery

The integrated battery must not be removed or replaced independently for safety reasons.

Maintenance and Inspection

Fully charge the battery before first use and ensure the product functions properly.
Charge the battery at least every 6 months to ensure optimal performance.
Inspect the product regularly, especially with prolonged use.

Battery Storage

Batteries should only be stored within a temperature range of -20 °C to +40 °C to ensure their safety and performance.
Do not store products with batteries in vehicles, as extreme heat above +40 °C can occur in the interior during high outdoor temperatures, causing damage or hazards such as overheating or fire.
Keep the product in a cool, dry, and well-ventilated place away from direct sunlight.

Disposal

The integrated battery must not be improperly disposed of. Observe the applicable regulations for the disposal of batteries and electronic devices in your region.
Burning, disassembling, or independently removing the battery is prohibited and can cause damage or hazards.

Note: The batteries built into this product are not classified as hazardous materials when used as intended.

Raptors LED Technik®
Ruth Schwob Str. 14
D-74924 Neckarbischofsheim

Tel.: +49 (0)7263 4087078
Mail.: info@raptors-led-technik.de

Average item rating

All reviews:

How do reviews work?

Total entries: 2

Sehr gutes Produkt
Produkt ist wirklich Klasse!
Lieferung war etwas lange. Da hat DHL etwas gepennt...

sd d , 04.02.2023 Verified purchase

Beinahe perfekt
Das Produkt ist teielweise beschädigt bei mir angekommen. Ob das jetzt an GLS oder am verkäufer liegt kann ich nicht sagen. Dazu kommt das einer der licht modi nicht funktioniert. Ansonsten ein sehr gutes produkt.

(Ps. Wen sich der verkäufer wegen den oben genanten punkten äusern würde. Würde ich mich sehr freuen.)

Max , 30.09.2024